More Blood Bowl Humans: Or, How I Learned to Stop Worrying and Love Gloss Varnish

 

DSC_3151
2 blitzers, a thrower, and 2 nothings (sorry… linemen)

(…with apologies to Stanley Kubrick.)

 

These were painted some time back, but due to every toy soldier painter’s worst nightmare (Matt Varnish) their debut into the wider world has been severely delayed.

In toy soldiers there are 2 vigorously pursued topics. What counts as “power-gaming” and what doesn’t. And, how to avoid disasters with matt varnish.

DSC_3153

Up until recently I had been relatively lucky. As a youngster I only really had plastic miniatures, and they were poorly painted, at best. They needed no varnish. As my painting developed I discovered a method (which has now been commercialised through Army Painter strong tone, and Devlan Mud before that) of base-coating the model then covering it with Chesnut Ink (oh how I wish GW still made the old Inks!! Nothing they have made since has been anywhere near as good and anyone who thinks it is better is just plain wrong!) and gloss varnish. Models were glossy, but they looked great.

DSC_3154

Then matt varnish sprays came along. The GW version was rubbish. I think I still have a can, which was used once and never again. The same went for Army Painter when they released an aerosol version. They both left a slight frosty finish and have just been used for terrain until they ran out.

My problems were all solved, or so I thought, when I discovered Testors Dullcote, though its cancer causing properties have seemed to make it only sporadically available ever since. And the last time I used it, the dreaded frosty finish resulted.

I have experimented with artists matt varnishes to mixed effect. The brush-on varnish of choice in the UK seems to be Daler Rowney (which is not easily available in the Antipodes) however the need to decant it seems to be too much faffing about to me.

DSC_3165

Eventually, I tried Vallejo brush on Matte Varnish and on an experimental figure I slathered it on as thick as I could, and it came up a treat. I did the same for these chaps, however, and disaster struck; after the varnish dried, they were all covered in a thick white film!

Number 10 linesman was subjected to all sorts of debased humiliations as I bathed him in various different solvents to try to remove the outer layer of varnish whilst leaving the paint underneath unaffected; all to no avail!

DSC_3158

Eventually, I discovered that if the model was re-coated in gloss varnish the white stuff would be dissolved and the model, albeit now high-gloss, totally fine! Huzzah! These figures seemed cursed as 2 other methods of matt varnishing also failed. In all, these figures have about 15 coats of varnish on them! The colours have been slightly affected by the many layers of varnish the light must reflect through.

The white stuff, I gather, is matting agent. Basically talcum powder or something similar dissolved in the carrier. It works by making the surface of the model (imperceptibly) rough, so light is absorbed instead of being reflected. Gloss varnish creates a perfectly smooth surface hence light bounces off. I guess this is why people decant their matt varnish, to get the ratio of matting agent perfect.

Instead, I discovered Tamiya Flat Clear in aerosol cans, and if they ever stop making this stuff  I will just live with super-shiny models. I have used Tamiya Flat Clear in all sorts of inappropriate conditions with no ill effect. It is the most flat varnish I have ever used. In all, it is perfect. That being said, I have noticed it seems to be taking more and more coats to cover up the gloss effect and sometimes the models still have a slight sheen (see my Estalians for example)….. damn! Does this torture never end?

DSC_3171
The whole team so far

 

Anyway, my current method is as follows: coat the figure in 3 coats of Feast & Watson high gloss polyurethane varnish leaving at least 24 hours between each coat. Always buy the smallest tin possible because it seems to go yellow if left in the tin unused for a long time. After that, spray with one or two coats of Tamiya Flat Clear.

I have tried Feast & Watson matt polyurethane as a brush on matt varnish and it was fine except that it seemed to be somehow even more glossy than the gloss varnish. The same phenomenon was observed with Wattyl Matt Estapol which was recommended on WargamerAU. Hmmm.

Advertisements

4 thoughts on “More Blood Bowl Humans: Or, How I Learned to Stop Worrying and Love Gloss Varnish

  1. You must have the patience of a saint mate – I only ever varnish if I’m adding a gloss effect to a specific part of a model, not for general protection purposes… These Bloodbowl minis look great though, and very well protected! I would fancy their chances in a bomb blast 🙂

    Liked by 1 person

    • Cheers, mate 🙂

      I always varnish. Plastic models probably don’t really need it unless you store them all just dumped in a tub together but I find metal minis chip if you don’t. Also I use lots of inks etc when I paint so if I don’t varnish the minis have lots of spots of differing levels of matte and shiny all over them; varnishing ties it all together I find!

      Liked by 1 person

      • Just stumbled onto your blog again at random and didn’t realise it was yours until I saw the ‘alternative townhouse’ post 🙂

        RE: Wattyl Matt Estapol – I swear by this, but only the spray version. The brush-on version tends to dry glossy for me too. (Strangely, the first pot I bought years ago was genuinely matt, but every pot since has turned out glossy. Other brands such as Carbothane Clear have had the same problem.)

        Usually I brush on a gloss coat onto metal minis, as well as onto any oft-handled bits of plastic minis, like the shoulder pads of Space Marines. Once dry, I spray matt coat onto the minis to remove the shine. It does have a slight satin finish and can dull the colours, so I sometimes do a final quick drybrush highlight over the top afterwards (particularly on metallics). It can also slightly yellow white, but again you can paint over it.

        I’ll have to check out Tamiya Flat Clear though – sounds like it might be a better option.

        My trusty test model before each spraying, Guardian Bob the Eldar, has about twenty coats of varnish on him now. In the event of a meteorite strike on the house he’ll be the only thing that survives.

        Liked by 1 person

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s